GPSCAN - Up to 100Hz CAN GPS Receiver
GPSCAN
Our latest CAN based GPS receiver that is much more than simple GPS. It is used for testing trains, tires, cars, rally cars, race motorcycles etc...
GPSCAN can be built with very fast 100Hz GPS for applications needing the lowest possible latency. Our devices are used in many drag race motorcycles/cars and is used to control the launch and traction control systems. Check here how fast it is.
GPS
Device can be equipped with any GPS receiver, even a receiver with an accurate L5 band is available.
Construction
Lightweight but still strong, made to anodized aluminum casing. Weatherproof since potted.
Other advantage is that the cheap antenna is separate and the receiver itself can be installed into a safe location.
Compatibility
Compatible with any CAN system, we have DBC file available to make install simple and fast.
MoTeC Compatibility
Plug & Play with all MoTeC devices, M1 ECU, displays, loggers etc...
Replacement for RaceGrade GPS devices, now included with MoTeC STC emulation and MoTeC GPS Async template.
Pictures
Optional - GPS Pulse
GPS Pulse is a feature where the GPS will send pulses and can be connected to any digital input. So, now GPS speed can be used by any ECU, even without serial or CAN bus. Check here how the GPS Pulse is used by one of our customers.
Optional - RalliTimer
RalliTimer is a new feature that can be used to time rally stages. Timer measures stage times, both directions automatically. GPSCAN/RTKCAN is powered from the phone so no connections to the car are needed.
Specification
GPSCAN | |
Supported systems |
Any system supporting CAN bus, DBC available. |
GNSS systems |
100Hz: GPS 50Hz: GPS+GLONASS SA 25Hz: GPS+GLONASS+GALILEO+BEIDOU+QZSS HA 25Hz: GPS+GALILEO+BEIDOU |
Accuracy |
SA: 2m HA: <0.4m |
Supported Bands |
SA: L1 or HA: Multiple bands |
Output rates |
25Hz, 50 or 100Hz |
Supported CAN types |
CAN 2.0b. (J1939 or NMEA 2000 is not supported) |
CAN ID |
Default: 0x21C |
CAN Speeds |
500k or 1Mbit. Default: 1Mbit/s |
GPS Lean Angle | Yes, FW > 1.3 |
MoTeC STC Emulation |
Yes, starting from FW > 1.4 |
Optional RalliTimer |
Timing system for Rally cars with start/finish beacons that flip when needed. FW > 1.3 |
Optional Serial Speed |
OFF by default, speed fixed to 230k. Can be deactivated. |
Optional GPS Pulse |
OFF by default but can be activated. External pullup required. Emulation is Hall sensor type. VR sensor output is not supported |
Optional Temperature sensor input |
Input for 16 channel IR Temperature sensor. |
Operating voltage | 5-32V |
Current requirement | Minimum of 200mA is required |
Current consumption (12V) |
Searching: 80mA GPS Fix: 75mA |
LED | Yellow (SA), Blue (HA), Red (50Hz), White (100Hz) |
Construction | Potted |
Material | Aluminum, anodized black |
Weight | 67gr |
Dimensions | 68 x 27 x 17mm |
Connector | Made to spec |
Warranty |
2 years (Antenna excluded) |
Pinout and Wiring
1 | GND | Black | |
2 | Optional - Serial TX | Blue | NMEA output |
3 | Optional - GPS Pulse | Orange | External pullup is required. |
4 | CAN - Lo | Green | 120ohm Terminating resistor is required |
5 | CAN + Hi | White | 120ohm Terminating resistor is required |
6 | Battery + | Red | 7-32V |
Yellow | Do not connect, only for firmware updates |
120ohm Terminating resistor is required for the CAN
Status Light
Led light indicates the status of the GPS.
Led Status | |
Power up | Led blinks once indicating power is connected. |
Off | No GPS available, searching. |
Blinking 1/sec | 3D GPS Fix is available |
Documents
Availability: Now, Contact us to reserve yours or for more details and pricing.
Links
- Approved antennas
- Check RTKCAN if you need the ultimate accuracy